As to increases in brain tumors tied to cell phone use, it’s too early to tell due to a lack of hard data, says Dr. Carlo. “We’re never going to see that in time to have it matter. Here in the US, we’re six years behind in getting the brain tumor database completed, and currently the best data are from 1999. By the time you see any data showing an increase, the ticking time bomb is set.”
The next scientific step will be to determine what this means for humans. The peer-reviewed papers will be passed on to the US Food and Drug Administration, which is responsible for determining human risk and issuing any guidelines to the public, and the Federal Communications Commission, which develops safety standards for cell phones. The FDA was part of the group of federal agencies who commissioned the studies back in the early 2000s.
Some products (http://www.safecell.net/reports01.html for example) are tested using a piece of shielding material in a laboratory test jig. These tests legitimately show the amount of radiation which penetrates the shield, but results will be very different when compared to putting a small amount of the same shield on a large transmitter like a cellphone. Remember, the entire phone radiates. Placing a small amount of shielding, even if it is an effective shielding material, only shields that small area at best. Think about this analogy: no light will penetrate a penny as it is a very effective light shield, but it is silly to think that holding a penny up to the sun will put you in darkness.
Phone radiation isn’t like the radiation from, say, a nuclear meltdown. That’s what’s known as “ionizing” radiation — it’s high energy and capable of damaging your DNA, which researchers have determined leads to cancer. Phones emit a much lower energy radiation (lower even than visible light) that’s considered to be “non-ionizing.” We know non-ionizing radiation doesn’t damage DNA the way that ionizing radiation does. But the question remains whether it could still react with the body in some other way that might lead to problems from longterm exposure.
Searching PubMed for studies published in the past 10 years, we found 102 studies that ultimately resulted in 12 relevant systematic reviews. To limit bias in our assessment of the literature, we used a validated critical appraisal tool called AMSTAR to determine the quality of each review. Eight of the reviews were critically low quality, two were low quality, and two were moderate quality.
There are alternate technologies that can be considered when looking to reduce cell phone radiation exposure which we don’t use. Why don’t we use them? Incorporating technologies such as antennas into a case can greatly reduce outgoing cell phone radiation levels when close to the cell tower, but not totally. If farther away, the cell phone signal levels increase, as does the radiation exposure to the body, possibly to unacceptable output power levels. This design does not reduce radiation exposure from the WiFi and Bluetooth RF because cell phones do not have the capacity to reduce their power levels whether or not an antenna is present. Maybe just as important, this design does not have the shielding capacity for ELF emissions which have the same dangers as the RF emissions. Other device attachments like buttons and stickers are minimally effective to totally ineffective, with no scientific basis. In short, there are no other technologies capable of up to eliminating all of the many potentially harmful cell phone emissions from hitting the body.
At high power levels, RF waves can heat up water molecules (which is how microwave ovens work). Scientists used to focus their concerns on the possibility that such heating of human tissue, which is mostly water, might damage cells. In fact, the FCC’s test of cell-phone emissions—which was set in 1996 and which all phones must pass before being allowed on the market—is based on that effect.
But, like the human studies, one can pick apart the NTP studies too. For one thing, the animals experienced cell phone radiation that was different from what humans live with. As Bucher said in a statement, “In our studies, rats and mice received radio frequency radiation across their whole bodies. By contrast, people are mostly exposed in specific local tissues close to where they hold the phone. In addition, the exposure levels and durations in our studies were greater than what people experience.”
When you make a phone call, just flip the shielded front cover down when you put the phone against your head. It’s that simple. By keeping the shielded front cover closed while against any part of your body, a barrier is created to protect from a broad spectrum of potentially harmful cell phone radiation emissions, yet won’t affect signal quality. You can use your cell phone with a higher sense of safety by simply keeping the shielded flip cover between your body and radiation-emitting source.
The outside is made of a synthetic polyurethane that feels just like leather, although genuine leather will be available soon. The inside is made of a microfiber that won’t scratch the phone. The materials are also designed to protect your phone, should you drop it. Most importantly, an integrated FCC-certified lab tested radiation-shielding foil not only deflects and absorbs RF, ELF and Thermal radiation to greatly reduce your exposure, but it also blocks RFID signals, so that hackers cannot steal your credit card information by scanning it from afar. And no, the case will not affect phone or battery performance.
Bonus application! In addition to shielding magnetic fields, PaperSHIELD is also quite good at shielding radiowaves (cellphone, wifi, etc). And because of the adhesive backing, it can be adhered to almost any surface you need such as the inside or back of your cellphone case. (Use a near field meter to test RF shielding performance.) Note that it is not transparent, so it can't be used on the touch screen side. Cover the cut edges with sturdy tape as they can be sharp. 36 inches wide. Made in USA.
Moving the meter around the case, we detect readings on the side, back and front of the case. We use the multi-directional TES 593 meter which measures 10 MHz to 8GHz. We use the unit of micro-watts per square centimeter, which looks like this little symbol: μW/cm² and we use it on the max setting which shows the maximum measured value. In non-science speak: the highest level of RF we see, which could be from the back the side or the front. 

Over time, the number of cell phone calls per day, the length of each call, and the amount of time people use cell phones have increased. Because of changes in cell phone technology and increases in the number of base stations for transmitting wireless signals, the exposure from cell phone use—power output—has changed, mostly lowered, in many regions of the United States (1).

×